Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Blog Article
How do you actually feel in relation to How to Install a Bathtub Yourself?
Mounting a tub isn't exactly brain surgery, however it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably challenging task. If the old tub is easily accessible, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and also position the brand-new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require an assistant to vacate the old tub and set in the new one. Ensure you have qualified yourself for the task as well as are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed job, it is much better to think about employing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This article will help you install a new bathtub in your washroom if you have actually currently purchased a brand-new tub as well as don't need to change the setup of your previous supply of water pipes.
Your devices and product checklist should consist of the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, turn on the taps to drain any type of water staying in the system. The procedure of eliminating the existing faucets can be rather troublesome because of the restricted gain access to that is commonly the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will originate from the pipelines. Once the supply pipes have actually been eliminated, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from transforming throughout this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing compound.
Before proceeding to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washing machines remain in location between the faucet and also the sink. Safeguard the faucet in place with the maker provided backnut. Once the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular tap adapters. The previous kind must be attached to the faucet ends first, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Using the two wood boards under its feet, position the bath tub in the required position. The wooden boards are practical in equally spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small points.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level as well as changing the feet on the bathtub until the level checks out level.
To install faucets, fit the bottom of the furthest flexible faucet port to the suitable supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Turn on the water system as well as check all joints as well as brand-new pipework for leakages and tighten them if essential. Load the bath tub and likewise check the overflow outlet and the regular electrical outlet for leakages.
Ultimately, repair the bathroom paneling as defined in the maker's user's manual. Tiling and also securing around the bath tub should wait up until the bath tub has been utilized at least once as this will resolve it right into its final position.
Planning for the Installment
Firstly, the sustaining frame provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final position.
Tiling Around the Bath tub
In the location where the bath fulfills the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall in between the bath as well as the tiling, leading to difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your components as well as fittings. They are marketed in tubes and cartridges, as well as can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill the bathtub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealer can crack relatively early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily available on the marketplace. It is recommended to fit the tiles using waterproof or waterproof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that entry on A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the search engines. You should take a moment to promote this write-up if you enjoyed reading it. Many thanks for taking the time to read it.
Book Now Report this page